Software

Ya se trate de controladores, el software, el dispositivo Gigaset QuickSync u otros: Aquí encontrará todas las descargas de soporte disponibles para su producto. (Si usted está buscando un manual, por favor vaya a "Downloads"> "Manuales").

Por favor, seleccione un producto.


Downloads

Version 0.1.4

Gigaset DX600A ISDN

User manual DX600A ISDN - New and updated functions V01 es

Valid for the following products:
Gigaset DX800A all in one, DX600A ISDN, DL500A 


Firmware update (version 172) 11/2014
 

  • Support of handsets with touch based user interface Gigaset SL910H, S820H, SL930H
  • Support of Gigaset Repeater 2.0
  • Full support for handsets: C430H/C530H/CL540H/E630H/C620H
  • Country specific call progress tones are supported.
  • AM Box selection and line selections functionality is now available on the SL930 handset 

Detailed information about this update can be downloaded here:

Firmwareupdate (version 158) 04/2014

Download detailed information about this update here:

Firmware update (version 96) 04/2012 

Improvements for Version 96:

Corrected: DTMF signals were dialed too fast from phonebook

Corrected: In some cases the wrong message was played for Answering Machine 3

Only in Combination with HC450: In some cases the door bell menu was not handled correct

In some case during an incoming call on the answering machine the fax detection did not work

In very rare cases during the registration of handset the base might have lost its registration data

In WebUI, only when using Internet Explorer, buttons to allow external access from other networks             for remote management were overlapped and not configurable.

For DX800: Corrected: when using provider voip4all: Call stops after 6 minutes

Detailed information about this update can be downloaded here:

Firmware update (version 94) 12/2011

  • Compatibility issue corrected, when handsets SL55/SL56/S67/S68/C47/E49 were newly registered on version 93.
  • Please reregister these handsets after updating to version 94.

Detailed information about this update can be downloaded here:

Firmware update (version 70) 08/2011 

Firmware updates actualize the software in your base system.

Important Security-Update for Gigaset DX600A ISDN:

Re-start of Basestation, when “110” or “112” are dialed.

Topic:
After updating from Firmware Version 34 (or lower) to Version 62 (or higher), in some cases and under special conditions the basestation Gigaset DX600A ISDN will be re-started, when at the basestation or from an handset the numbers “110” or “112” were dialed. This topic after dialing “110” or “112” only occurs, if before a firmware update via Internet was performed. In factory delivery state of Gigaset DX600A ISDN and with all newer software versions delivered for this model, this topic will not occur.


Solution:

This topic is solved by updating to the actual firmware version 65 (or higher). Customers, who updated from a former version (34 or lower), are urgently recommended to immediately update to version 65 (or higher).

Improvements in Version 70:

  • Accelerated acceptance of incoming call on handsets in analogue and ISDN-connections
  • Portugal Version: Call Forwarding in PT network again working (Correction from version 69).

 

Detailed information about this update can be downloaded here:

 

 

Firmware update (version 69) 05/2011 

Firmware updates actualize the software in your base system.

Important Security-Update for Gigaset DX600A ISDN:

Re-start of Basestation, when “110” or “112” are dialed.

Topic:
After updating from Firmware Version 34 (or lower) to Version 62 (or higher), in some cases and under special conditions the basestation Gigaset DX600A ISDN will be re-started, when at the basestation or from an handset the numbers “110” or “112” were dialed. This topic after dialing “110” or “112” only occurs, if before a firmware update via Internet was performed. In factory delivery state of Gigaset DX600A ISDN and with all newer software versions delivered for this model, this topic will not occur.


Solution:

This topic is solved by updating to the actual firmware version 65 (or higher). Customers, who updated from a former version (34 or lower), are urgently recommended to immediately update to version 65 (or higher).

Improvements in Version 69:

  • AM-List corrected, were in some cases (when CLIP was not provided) the last number was shown
  • Improvements displaying CLIP-Info for UK-variant
  • Fix for line current detections implemented (for analogue network)
  • Improvements when using devices in the Italian ISDN-network
  • Currency symbol “€” removed, when call charge is displayed (only for ISDN)
  • In seldom cases occurring blocked call forwarding menu is fixed

Detailed information about this update can be downloaded here:

 

 

Gigaset DX600A ISDN factory default sounds

Gigaset DX600A ISDN factory default sounds

Default ringtones