Service für Gigaset C570

Gigaset C570
Willkommen beim Kundenservice für Ihr Gigaset C570. Auf dieser Seite finden Sie Antworten zu häufig gestellten Fragen. Sowohl Bedienungsanleitungen wie auch Soft- und Firmware stehen zum herunterladen bereit. Ebenfalls finden Sie hier Videotutorials, die Ihnen bei der Einrichtung helfen. Wenn Ihr Produkt einen Defekt aufweist, können Sie Ihr Gigaset C570 zur Reparatur anmelden. Außerdem finden Sie hier ubehör für Ihr Gigaset C570. Sollten Sie nach Produkten für Ihr Gigaset C570 suchen, finden Sie Informationen dazu in unserer Kompatibilitätsdatenbank. Hier finden Sie auch Hilfestellung zum Registrieren Ihres Gigaset C570 mit anderen Geräten.

Antworten auf häufig gestellte Fragen

Sie haben Fragen zu Ihrem Gigaset Produkt? Hier erhalten Sie Antworten.

Top 10 FAQs

  • First steps for troubleshooting
  • Base reset
    • Unplug the power-supply unit from the socket.
    • Press and hold down the paging key on the base station.
    • Plug in the power-supply unit again.
    • Keep the paging key on the base station pressed.
    • Release the paging key after 3 seconds.


    PLEASE NOTE! The entire contents of the memory will be deleted. All portable handsets will be deregistered. The system code will be reset to 0000.

  • Notes on operating a Gigaset phone on the analog telephone connection of a router or modem

    If you operate your Gigaset on the telephone connection of a router/modem, make sure that you have noticed the following points:


    • Use the phone cable from the Gigaset packaging.
    • If the router or modem does not have a phone jack, it is necessary to use the enclosed phone cable or the enclosed phone adapter of your router/modem.
    • Connect the cable to the router`s phone jack / phone port / FON port.
    • Please check if your telephone data (internet telephone number, provider-profile, …) for the used telephone connection in the router/modem were entered correctly.
    • Please make sure that your internet connection is working.


    If the problem persists, please contact your provider.

  • Notes on Caller ID (CID)

    By default, the number of the caller is shown in the display of your Gigaset telephone. You do not have to make any other settings on your Gigaset telephone. However, if the caller's number is not displayed, this can be due to the following:

    - You have not ordered CID from your network provider or
    - Your telephone is connected through a PBX that does not transmit all information.

    Is your telephone connected through a PBX/gateway?
    You can establish this by checking for an additional device connected between your telephone and house connection, e.g., a PBX, gateway etc.
    In most cases, simply resetting this device will remedy the situation:
    - Briefly disconnect the power plug of your PBX.
    - Re-insert the plug and wait for the device to restart.

    If the caller number is still not displayed:
    Check the CID settings of your PBX and activate this function if necessary. In the user guide for the device, search for the term "CID" (or an alternative term such as "phone number transmission", "caller ID", ..).

    If necessary, contact the device manufacturer. If this does not resolve the problem, it is possible that your network provider does not support the CID service for this number.

    Have you ordered the CID service from your network provider?
    Check whether your provider supports Caller ID (CID) and that the function has been activated for you. If necessary, contact your provider.

  • Which batteries should I use for the Gigaset handset?

    Recommented batteries:

    For Gigaset handsets, use only the batteries approved by Gigaset. The high quality standard guarantees safe use and a long service life.
    NiMh round cells type AAA can be purchased in our Gigaset online shop.

  • Which Gigaset handsets are compatible with my router?

    To check the compatibility between your Gigaset handset and your router, please open our compatibility database.

    The main features of various device combinations are displayed here.

  • How can I register a repeater?
  • Why isn't there any picture in the display during an incoming call?

    To see a picture in the display in addition to the number from an internal caller you have to achieve the following settings:

     

    • At least one picture must be stored in the Media pool from the handset/base (via Gigaset QuickSync)
    • A directory entry must be dedicated to a picture in the directory entry options.
    • The caller must show his number for outgoing calls.
    • The Network provider must support the CLIP function and this function must be activated

    .
    Important Note:

     

    If a handset with picture-CLIP-function is registered to an older base station it could be possible that there is no picture shown in the display due to incompatibility reasons.

     

    In these cases please have a look at our compatibility database and choose your combination to see if it is possible or not.

     

    https://www.gigaset.com/hq/en/cms/PageCustomerServicesCompatibility.html


  • Why my handset does not ring when it is in the charging cradle?

alle FAQs nach Themen

  • A
  • B
    • Batterie
      • Which batteries should I use for the Gigaset handset?

        Recommented batteries:

        For Gigaset handsets, use only the batteries approved by Gigaset. The high quality standard guarantees safe use and a long service life.
        NiMh round cells type AAA can be purchased in our Gigaset online shop.

  • C
  • F
    • First steps for troubleshooting
      • First steps for troubleshooting
      • Notes on operating a Gigaset phone on the analog telephone connection of a router or modem

        If you operate your Gigaset on the telephone connection of a router/modem, make sure that you have noticed the following points:


        • Use the phone cable from the Gigaset packaging.
        • If the router or modem does not have a phone jack, it is necessary to use the enclosed phone cable or the enclosed phone adapter of your router/modem.
        • Connect the cable to the router`s phone jack / phone port / FON port.
        • Please check if your telephone data (internet telephone number, provider-profile, …) for the used telephone connection in the router/modem were entered correctly.
        • Please make sure that your internet connection is working.


        If the problem persists, please contact your provider.

  • N
    • Notes on Caller ID (CID)
      • Notes on Caller ID (CID)

        By default, the number of the caller is shown in the display of your Gigaset telephone. You do not have to make any other settings on your Gigaset telephone. However, if the caller's number is not displayed, this can be due to the following:

        - You have not ordered CID from your network provider or
        - Your telephone is connected through a PBX that does not transmit all information.

        Is your telephone connected through a PBX/gateway?
        You can establish this by checking for an additional device connected between your telephone and house connection, e.g., a PBX, gateway etc.
        In most cases, simply resetting this device will remedy the situation:
        - Briefly disconnect the power plug of your PBX.
        - Re-insert the plug and wait for the device to restart.

        If the caller number is still not displayed:
        Check the CID settings of your PBX and activate this function if necessary. In the user guide for the device, search for the term "CID" (or an alternative term such as "phone number transmission", "caller ID", ..).

        If necessary, contact the device manufacturer. If this does not resolve the problem, it is possible that your network provider does not support the CID service for this number.

        Have you ordered the CID service from your network provider?
        Check whether your provider supports Caller ID (CID) and that the function has been activated for you. If necessary, contact your provider.

  • P
    • Picture CLIP
      • Why isn't there any picture in the display during an incoming call?

        To see a picture in the display in addition to the number from an internal caller you have to achieve the following settings:

         

        • At least one picture must be stored in the Media pool from the handset/base (via Gigaset QuickSync)
        • A directory entry must be dedicated to a picture in the directory entry options.
        • The caller must show his number for outgoing calls.
        • The Network provider must support the CLIP function and this function must be activated

        .
        Important Note:

         

        If a handset with picture-CLIP-function is registered to an older base station it could be possible that there is no picture shown in the display due to incompatibility reasons.

         

        In these cases please have a look at our compatibility database and choose your combination to see if it is possible or not.

         

        https://www.gigaset.com/hq/en/cms/PageCustomerServicesCompatibility.html


  • R
    • Reset Prozedur
      • Base reset
        • Unplug the power-supply unit from the socket.
        • Press and hold down the paging key on the base station.
        • Plug in the power-supply unit again.
        • Keep the paging key on the base station pressed.
        • Release the paging key after 3 seconds.


        PLEASE NOTE! The entire contents of the memory will be deleted. All portable handsets will be deregistered. The system code will be reset to 0000.

    • Repeater

Downloads

Hier erhalten Sie Bedienungsanleitungen und Software-Updates.
Manuals
  • Gigaset C570 Bedienungsanleitung de de at

Firmware
Software

Mobilteil anmelden

Sie besitzen eine Gigaset C570 Basisstation und wollen ein Mobilteil anmelden? 
Das Gigaset C570 mit einem Mobilteil koppeln

Nicht fündig geworden?

Kontaktieren Sie den Gigaset Kundenservice für persönliche Hilfestellung.