Service für Gigaset SL370

Gigaset SL370
Willkommen beim Kundenservice für Ihr Gigaset SL370. Auf dieser Seite finden Sie Antworten zu häufig gestellten Fragen. Sowohl Bedienungsanleitungen wie auch Soft- und Firmware stehen zum herunterladen bereit. Ebenfalls finden Sie hier Videotutorials, die Ihnen bei der Einrichtung helfen. Wenn Ihr Produkt einen Defekt aufweist, können Sie Ihr Gigaset SL370 zur Reparatur anmelden. Außerdem finden Sie hier ubehör für Ihr Gigaset SL370. Sollten Sie nach Produkten für Ihr Gigaset SL370 suchen, finden Sie Informationen dazu in unserer Kompatibilitätsdatenbank. Hier finden Sie auch Hilfestellung zum Registrieren Ihres Gigaset SL370 mit anderen Geräten.

Antworten auf häufig gestellte Fragen

Sie haben Fragen zu Ihrem Gigaset Produkt? Hier erhalten Sie Antworten.

Top 10 FAQs

  • First steps for troubleshooting
  • Base reset
    • Unplug the power-supply unit from the socket.
    • Press and hold down the paging key on the base station.
    • Plug in the power-supply unit again.
    • Keep the paging key on the base station pressed.
    • Release the paging key after 3 seconds.


    PLEASE NOTE! The entire contents of the memory will be deleted. All portable handsets will be deregistered. The system code will be reset to 0000.

  • Notes on operating a Gigaset phone on the analog telephone connection of a router or modem

    If you operate your Gigaset on the telephone connection of a router/modem, make sure that you have noticed the following points:


    • Use the phone cable from the Gigaset packaging.
    • If the router or modem does not have a phone jack, it is necessary to use the enclosed phone cable or the enclosed phone adapter of your router/modem.
    • Connect the cable to the router`s phone jack / phone port / FON port.
    • Please check if your telephone data (internet telephone number, provider-profile, …) for the used telephone connection in the router/modem were entered correctly.
    • Please make sure that your internet connection is working.


    If the problem persists, please contact your provider.

  • Notes on Caller ID (CID)

    By default, the number of the caller is shown in the display of your Gigaset telephone. You do not have to make any other settings on your Gigaset telephone. However, if the caller's number is not displayed, this can be due to the following:

    - You have not ordered CID from your network provider or
    - Your telephone is connected through a PBX that does not transmit all information.

    Is your telephone connected through a PBX/gateway?
    You can establish this by checking for an additional device connected between your telephone and house connection, e.g., a PBX, gateway etc.
    In most cases, simply resetting this device will remedy the situation:
    - Briefly disconnect the power plug of your PBX.
    - Re-insert the plug and wait for the device to restart.

    If the caller number is still not displayed:
    Check the CID settings of your PBX and activate this function if necessary. In the user guide for the device, search for the term "CID" (or an alternative term such as "phone number transmission", "caller ID", ..).

    If necessary, contact the device manufacturer. If this does not resolve the problem, it is possible that your network provider does not support the CID service for this number.

    Have you ordered the CID service from your network provider?
    Check whether your provider supports Caller ID (CID) and that the function has been activated for you. If necessary, contact your provider.

  • Which batteries should I use for the Gigaset handset?

    Recommented batteries:

    For Gigaset handsets, use only the batteries approved by Gigaset. The high quality standard guarantees safe use and a long service life.
    NiMh round cells type AAA can be purchased in our Gigaset online shop.

  • For which purposes can I use the integrated bluetooth functionality?

    The bluetooth functionality was integrated to

    • use the handset in combination with a cordless bluetooth headset
    • copy telephone book entries (as VCards) via bluetooth
    • synchronize contacts from your PC (surrogate for data cable)
  • Bluetooth accessory can not be registered to the S68H handset

    Please check, whether the Bluetooth accessory supports one of the

    given protocols, which are supported by the Gigaset handset:

    • headset profile (for Bluetooth headsets)
    • serial port profile (for PC connection)
    • OBject EXchange Profile (OBEX)

     

    When

    the Bluetooth accessory was installed already, please delete the

    registration from the handset:

    • Bluetooth Menu
    • Known Devices
    • Select the accessory, e.g. a headset
    • Options
    • Delete Entry

    If it is again not possible to register the accessory to the handset, please check, whether the accessory supports a reset-function, and execute it. Please pay attention that perhaps previous settings will be deleted in the accessory.

     

    If you would like to use a headset already registered to another device (e.g., to a mobile phone) with your desktop phone, please deactivate this connection before you start the registration process.

  • What has to be noticed in case of an incoming call?

    An incoming call will also be signalized at the bluetooth headset and can immediately be accepted by pressing the 'Accept button' (see manual of your bluetooth headset producer).

     If you accept the call with your Gigaset S68H device, and afterwards want to transfer the call to your headset, you also just need to press the accept button at your headset.

    In this case, the transfer of the call could take between 3 and 5 seconds. Within this period you should avoid to press the accept button twice, because you possibly could hang up the call.

  • How man bluetooth devices can be managed by the Gigaset S68H?

    You are able to register up to 6 bluetooth devices, but just one bluetooth headset.

  • Which format is needed to exchange pictures?

    The Gigaset S68H device supports pictures with Bitmap format (bmp) at a size of 128 x 160 pixel.

alle FAQs nach Themen

  • B
    • Bluetooth
      • Bluetooth accessory can not be registered to the S68H handset

        Please check, whether the Bluetooth accessory supports one of the

        given protocols, which are supported by the Gigaset handset:

        • headset profile (for Bluetooth headsets)
        • serial port profile (for PC connection)
        • OBject EXchange Profile (OBEX)

         

        When

        the Bluetooth accessory was installed already, please delete the

        registration from the handset:

        • Bluetooth Menu
        • Known Devices
        • Select the accessory, e.g. a headset
        • Options
        • Delete Entry

        If it is again not possible to register the accessory to the handset, please check, whether the accessory supports a reset-function, and execute it. Please pay attention that perhaps previous settings will be deleted in the accessory.

         

        If you would like to use a headset already registered to another device (e.g., to a mobile phone) with your desktop phone, please deactivate this connection before you start the registration process.

      • For which purposes can I use the integrated bluetooth functionality?

        The bluetooth functionality was integrated to

        • use the handset in combination with a cordless bluetooth headset
        • copy telephone book entries (as VCards) via bluetooth
        • synchronize contacts from your PC (surrogate for data cable)
      • How man bluetooth devices can be managed by the Gigaset S68H?

        You are able to register up to 6 bluetooth devices, but just one bluetooth headset.

      • How many entries can be sent/received?

        You're able to send/receive up to 250 entries as VCard format.

      • Is it possible to send/exchange VCards in combination with a picture?

        If you want to transfer an directory / phone book entry with VCard format from a mobile phone to you Gigaset handset, this basicly is possible.

        A picture stored to the entry in the mobile phone will not be transfered to the Gigaset, due to limited storage in the Gigaset handset.

        After you have transfered the entry you can add again a picture manually using the Siemens Quicksync software and assign it to the directory entry manually in the phone.

      • Is it possible to use the hardware- and bluettooth interface simultaneously?

        No, if the bluetooth functionality is activated, the hardware interface (Slim Lumberg) is deactivated.

        The charging function isn't affected of course.

      • What can I do in case of connectivity problems?

        If connectivity problems between Gigaset S68H and your bluetooth headsets occurs, you should test the following

        • reset the bluetooth headset reffering to the manufacturers documentation
        • delete the bluetooth registration ('Known devices') at your Gigaset S68H
      • What has to be noticed in case of an incoming call?

        An incoming call will also be signalized at the bluetooth headset and can immediately be accepted by pressing the 'Accept button' (see manual of your bluetooth headset producer).

         If you accept the call with your Gigaset S68H device, and afterwards want to transfer the call to your headset, you also just need to press the accept button at your headset.

        In this case, the transfer of the call could take between 3 and 5 seconds. Within this period you should avoid to press the accept button twice, because you possibly could hang up the call.

      • Which Bluetooth headsets are recommended for the Gigaset SL56, SL37 and S68H?

        Whether Bluetooth® devices can communication with each other is a profile question. It is important that they support and use the same profile for different functions.

        The Gigaset products Gigaset SL56, SL37 and S68H support the Headset Profile (HP) for communication with a headset, so you can operate headsets on your Gigaset handset that supports the Headset Profile.

        Here is a list of successful tested headsets recommended for operation with the Gigaset SL56, SL37 und S68H.

        Anycom Aris-21
        Anycom DYO
        BenQ-Siemens HHB 500
        BenQ-Siemens HHB 600
        Motorola: Bluetooth-Headset HS820
        Bluetooth-Headset Jabra BT205
        Bluetooth-Headset Jabra BT250
        Bluetooth-Headset Jabra BT800
        Bluetooth-Headset Jabra BT2020
        Bluetooth-Headset Jabra BT3030
        Bluetooth-Headset Jabra BT5020
        Bluetooth-Headset Jabra BT8040
        Plantronics M2500
        Ericsson HBH 20
        GN Netcom GN6210
        Plantronics Voyager 510
        Plantronics Voyager 520
        Plantronics Voyager 855
        Plantronics Discovery 665
        Sony Ericsson HBH 608
        Nokia BH 800

      • Which bluetooth profiles are supported by the Gigaset SL56, SL37 and S68H ?

        The Gigaset products Gigaset SL56, SL37 and S68H support the following Bluetooth® profiles:

        • Serial Port Profile (SPP) for data communication with a PC.
        • Headset Profile (HP) for communication with a headset.
        • OBject EXchange Profile (OBEX) for the transfer of address book entries (vCards).


      • Which format is needed to exchange pictures?

        The Gigaset S68H device supports pictures with Bitmap format (bmp) at a size of 128 x 160 pixel.

    • Batterie
      • Which batteries should I use for the Gigaset handset?

        Recommented batteries:

        For Gigaset handsets, use only the batteries approved by Gigaset. The high quality standard guarantees safe use and a long service life.
        NiMh round cells type AAA can be purchased in our Gigaset online shop.

  • C
    • Call list
      • [No Title]
        • Press the middle of the control key to open menu
        • Enter 8 5 7
        •  Select Missed Calls or All Calls
        • Confirm with OK
    • Charging
      • [No Title]

        When the handset switched off itself due to an empty battery and was not recharged for some hours, it can take up to 30 minutes until the display screen reactivates.

        In that case, the battery was extremely discharged and needs therefore time to reactive the display screen.

      • [No Title]

        Below some functions are listed that reduce the standby and operation time:

        • Bluetooth Please deactivate Bluetooth if you are not using it
        • Flashing of MWI (messages waiting indication) Please retrieve the messages until the flashing stops
        • Positioning of the device at the coverage limit Only recommended if no alternative exists. It is better to place base station and handset cradle with the handset near the base station
        • Frequent call receiving versus enduring calls. The handset has to handle information of the incoming call each time The handset has to display some of this information each time The display has to illuminate with full intensity each time. With an enduring call the intensity backspaces after a few seconds. The ringer tone has to appear each time
        • Activated illumination of the handset outside the recharging cradle Deactivate the illumination outside the recharging cradle. With a key press to the on hook key you can reactivate the display.
        • Baby phone or room monitoring In this mode the handset is nearly active like in an enduring call, and needs a lot more voltage than in idle mode.
        • Frequently use of the device / check settings If you check settings in the handset very often, the handset needs more voltage than in idle mode, due to the activated display, and the CPU load during this time.
      • [No Title]

        To provide a gentle charging of the handset batteries, the charging control switches off the charging of the portable handsets when a surrounding temperature of 30° - 35° degrees celsius has been reached. This is equivalent to a battery heat of about 40 - 45 ° Celsius.

        The switching off of the charging process is a demand of the battery manufacturer as the battery may affect a permanent damage if being overheated.

        • The customer should avoid to expose the device to direct solar radiation
        • The charging of the handset should be done at night if possible
        • The base station or charging unit should be placed in a cool place
        • The usage of a seperate charger is advisable.
        • These chargers can be placed, regardless from the base stations installation location, in some colder areas at the residence.
        • A replacement of the handset is not helpful at all and should be avoided in any case.
    • Connected to a PABX
      • [No Title]

        It is possible to deactivate the callers list.

        This leads to to the fact that no calls will be accepted anymore.

        To deactivate or activate the callers list follow this instruction:

        You now have the following options:

        • Open Menu 
        • Enter the figures 8 and 5 
        • Enter the following figures slowly: 9 4 7 6 2 0 0 5
        • You now have the following options: Press 1, to deactivate the callers list. Press 0, to activate the callers list.
        • Confirm with the OK softkey
  • D
    • Display
      • How can I change the display language?

        If the display language is adjusted so you can´t serve the handset, please follow the description:

        • Open the menu with the control key (Press the middle).
        • Enter the combination 8 - 4 - 1.
        • Now you can see the available languages of the handset.
        • Please choose the language you need and confirm it with OK.
      • How can I switch off or change the screensaver?
        • In the default setting a screensaver is activated in the handset
        • It is possible to change or switch off the screensaver by:
        • MENU
        • Press 8 3
        • Screensaver / Press OK
        • Activation : ON / OFF
        • Selection: Beach, Bowl, Feather, Ice, Sky, Sunflower, Village, Water surface, Waterdrops, Clock
      • [No Title]

        If the handset is in the base station or the charging cradle, the display is dimmed.

        If you take the handset from the base/charger the illumination switched off completely after 60 seconds, if you not press any key.

        You can switch off or on this function with:

        • Menu Settings (8)
        • Display (3)
        • Backlight (4)
        • Select Without charger and press ( = on). Press and hold (idle status).

        NOTE: If the illumination is switched on outside the charging cradle, the standby time for the handset is considerably reduced!

  • E
    • ECO DECT
      • [No Title]

        no inforamtion available

      • [No Title]

        Eco mode and any repeater support cancel each other out, i.e. both functions cannot be used at the same time.

      • [No Title]

        Just look for our newly developed “ECO DECT” logo, which can be found on the packaging of our ECO DECT phones.

      • [No Title]

        Siemens Gigaset is committed to effective and lasting environmental protection. Millions of cordless phones are used around the world. For this reason each energy saving has a considerable and positive impact. The use of the new technology also means that we react to market requirements and the needs and wishes of our customers.

      • [No Title]

        DECT stands for Digital Enhanced Cordless Telecommunications and is an international standard for cordless telephones. DECT systems use radio waves to transmit information between the handset and base station.

      • [No Title]
         

        Gigaset DECT handsets possess since many years an automatic adaptation of the transmitting power - depending on the distance to the base. Within a radius of 5-10 meters from the basestation the transmitting power of the handsets is reduced by 75%. The new ECO DECT function completes the adaptation. The transmitting power of the handsets and base is reduced to the minimum, when the handset is lying on the base.

         

         

         

      • [No Title]
         

        Yes, all Gigaset products are safe. The international limits for radio wave transmission ensure that there are no risks. Our products fall well below these recommended limits.

        Further information about the discussion on radio waves and health is provided by the World Health Organization at www.who.int/peh-emf/en/.

      • [No Title]

        ECO DECT saves energy and contributes therefore actively to the environmental protection. On the one hand, the transmission power of the base station is reduced to the minimum while lying on the base. On the other hand, an energy saving switching power supply leads to a 60% energy saving.

        Remark: The reducing of the transmission power is only possible if one (1) handset is run with the base.

  • F
    • First steps for troubleshooting
      • First steps for troubleshooting
      • Notes on operating a Gigaset phone on the analog telephone connection of a router or modem

        If you operate your Gigaset on the telephone connection of a router/modem, make sure that you have noticed the following points:


        • Use the phone cable from the Gigaset packaging.
        • If the router or modem does not have a phone jack, it is necessary to use the enclosed phone cable or the enclosed phone adapter of your router/modem.
        • Connect the cable to the router`s phone jack / phone port / FON port.
        • Please check if your telephone data (internet telephone number, provider-profile, …) for the used telephone connection in the router/modem were entered correctly.
        • Please make sure that your internet connection is working.


        If the problem persists, please contact your provider.

  • K
    • Kompatibilität
      • [No Title]
        The meaning of OPCAP

        Description: Open Platform For Cordless Applications

        The OPCAP interface allows you to control different applications with an Gigaset telephone.

        Therefore a registration of the device which shall become controlled has to be registered to the Gigaset base station.

        The handset Gigaset SL37H is able to display OPCAP menus. The Base station Gigaset SL370 and SL375 supporting the OPCAP interface.

        Example:

        • With OPCAP you are able to register the Gigaset M34 USB at the Gigaset SL560 / SL565 base station, to use the M34 functions. 
        • The supported functions are: VoIP calls through Skype (separate internet connection necessary) Remote control of PC programs Using of messenger programs such as MSN, Yahoo, ICQ, AOL and Skype. Configuration of the phone book
      • N
        • Notes on Caller ID (CID)
          • Notes on Caller ID (CID)

            By default, the number of the caller is shown in the display of your Gigaset telephone. You do not have to make any other settings on your Gigaset telephone. However, if the caller's number is not displayed, this can be due to the following:

            - You have not ordered CID from your network provider or
            - Your telephone is connected through a PBX that does not transmit all information.

            Is your telephone connected through a PBX/gateway?
            You can establish this by checking for an additional device connected between your telephone and house connection, e.g., a PBX, gateway etc.
            In most cases, simply resetting this device will remedy the situation:
            - Briefly disconnect the power plug of your PBX.
            - Re-insert the plug and wait for the device to restart.

            If the caller number is still not displayed:
            Check the CID settings of your PBX and activate this function if necessary. In the user guide for the device, search for the term "CID" (or an alternative term such as "phone number transmission", "caller ID", ..).

            If necessary, contact the device manufacturer. If this does not resolve the problem, it is possible that your network provider does not support the CID service for this number.

            Have you ordered the CID service from your network provider?
            Check whether your provider supports Caller ID (CID) and that the function has been activated for you. If necessary, contact your provider.

      • R
        • Registering
          • [No Title]
            • You can register up to a total of six hand-sets on your base station.
            • A GigasetSL56 handset can be registered on up to four base stations.
            • You must activate manual registration of the handset at both the handset and the base station.
            • After it has registered, the handset returns to idle status.
            • The internal number of the handset appears in the display, e.g. INT 1.
            •  If it does not, repeat the procedure.
            1. Press the middle of the control key
            2. Enter 8 4 3
            3. Select the base with the control key
            4. Press the right softkey OK
            5. Enter System PIN (0000)
            6. Press the right softkey OK

            On the base station:

            Within 60 secs. press and hold the registration/paging key on the base station (approx. 3 secs.)

        • Reset Prozedur
          • Base reset
            • Unplug the power-supply unit from the socket.
            • Press and hold down the paging key on the base station.
            • Plug in the power-supply unit again.
            • Keep the paging key on the base station pressed.
            • Release the paging key after 3 seconds.


            PLEASE NOTE! The entire contents of the memory will be deleted. All portable handsets will be deregistered. The system code will be reset to 0000.

          • Reset base
            • Unplug power supply
            • Hold down Paging key
            • Plug in power supply
            • Hold down Paging key at least for 3 seconds  
            • Release Paging key

             

            After that the reset is performed and all handset are deregistered

             

             

             

             

          • Reset handset
            • Switch off handset
            • Press 1, 4 and 7 and switch on the handset (SERVICE will appear)
            • Enter 4 6 8 5 4 6 3 (HOTLINE)
            • Handset switches off

             

            Handset is reset to the default setting (Phonebook and Redial list are empty)

             

             

             

             

      • S
        • Settings / Using / Handling
          • How can I switch off / change the screensaver?
            • In the default setting a screensaver is activated in the handset
            • It is possible to change or switch off the screensaver by:
            • MENU
            • Press 8 3
            • Screensaver / Press OK
            • Activation : ON / OFF
            • Selection: Beach, Bowl, Feather, Ice, Sky, Sunflower, Village, Water surface, Waterdrops, Clock
          • [No Title]

            You can turn off all ringer tones by pressing the star-key. In this case you will see the cancelled bell in the display.

          • [No Title]

            Every part of a gigaset model has its own label.

            • The base station
              The base station is that part of your Gigaset where the telephon cable is plugged in.
              At the bottom side of the base station you will find a lable with the description of the base station. Normally that is also the description of the whole Gigaset System.

            • The handset
              The handset is the mobile part of your Gigaset.
              In the battery compartment or at the battery cover you will find the description of the handset.
              If the Gigaset System has a seperate charging cradle, you will find the description of the handset at the bottom side of it too.

            • The charging cradle
              At some Gigaset models you have a stand-alone base station. In these cases the handset will be delivered with a seperate charging cradle. The cradle belongs to the handset and share its description. For example if you have a Gigaset SL56 the description of the cradle is SL56 charging cradle.
          • [No Title]
            • Open Menu
            • Enter 8 5 
            • Press OK to switch ON/OFF the music on hold
          • [No Title]

            Press the handsfree key during a call switch handsfree on or off.

          • [No Title]

            Enter the number and press the talk key. No dial tone after pressing the talk key?

            1. Please note, that you have to press and hold, the talk key to hear the dial tone. By pressing the talk key briefly you will open the redial list from the last 10 numbers.

            2. If you press the handsfree key you will hear the dial tone directly.

      • T
      • You can store exactly 250 phone book entries as type vCard in your handset Gigaset SL37 H. Each entry contains the following fields:

        First Name 16 figures
        Surename 16 figures
        Phone (Home) 32 numbers
        Phone (Office) 32 numbers
        Phone (Mobile) 32 numbers
        E-Mail 60 figures
        Anniversary Yes / No
        Caller Picture None / Picture
      • [No Title]

        After connecting sucessfully, synchronization can be carried out. The process of managing contacts is automatic.

        The contacts from the handset that is currently connected and the contacts from the selected database like Microsoft Outlook, Microsoft Outlook Express or Contacts on Microsoft Windows Vista on the computer are used.

        For proper synchronization and phone number conversion during synchronization with handset, Area Numbers should be properly entered. Please refer to handset User manual how to set your actual Area Numbers.

        The selected PC database and the connected handset are shown in the main application window.

        The contacts database on the computer can be changed in the Settings >> Contacts, see Settings - Contacts. Handset may be changed as described in Connecting to a handset.

        Fields which will be synchronized with handset:

        Data Field Maximum transferred charakters

        • First Name 16
        • Surname 16
        • Phone Home 32
        • Phone Office 32
        • Phone Mobile 32
        • E-mail 60 A
        • nniversary date and time Date only

        Fields' length on handset are limited. If transferred field from handset is longer it will be cut by handset. From phone numbers characters other than digits, asterisk '*', hash '#', 'p', 'P', 'r', 'R', plus '+' (only on first position) and comma ',' (transferred to Handset as pause character 'P') are dropped.

        To start synchronization:

        • Click the icon in the System Tray and select the option Synchronize .
        • Click the icon in the main window of the application.
        • Select the menu option File >> Synchronize .
        • The synchronization process uses the following rules: If there is the same contact with non-conflicting differences (for example: on the handset John Smith with a phone number and the same contact with the same number and an additional e-mail on the PC) the data on both the handset and in the computer database is updated.
        • A contact on the handset that is not in the computer database will be copied to the database. A contact in the computer database that is not on the handset will be copied to the handset according to the settings in the Settings >> Contacts tab, see Settings - Contacts tab .
        • To change the contacts synchronized to the handset please refer to the Filtering contacts dialogue, see Synchronization - Filtering .
        • If the contact is already synchronized, the next synchronization will update the contacts with those changes made since the last synchronization (for example a change in the phone number, adding new data).
        • The system shows the synchronization process with a single status line and progress bar. The user may interrupt the operation with the " Stop " button. When the operation is complete, the system notifies the user with the date and time of the last successful synchronization.
        • Conflicts: There may be conflicts if the user has changed data on both the handset and in the PC database since the last synchronization.
        • The application will handle conflicts according to the option Conflict resolution under the Settings >> Contacts tab, see Synchronization - Conflict resolving . If the option Let me resolve conflicts is active, an appropriate message will be shown when there is a conflict. Click the link " There are {...} conflicts to resolve. " to open the Conflict Resolving Dialogue dialogue.
        • No free entries on the handset If there are no more free entries on the handset an appropriate message will be shown after synchronization.
        • Click the link " Handset address book is full. Could not store {...} contacts " to open the Filtering contacts dialogue.
        • Remarks Contacts from the PC without any phone numbers will not be synchronized (they will be ignored by the software).
        • At least one number is mandatory. If the first name and surname fields are empty in the PC database, the phone number will be copied to the surname before synchronizing with the handset.
        • Handset has limited set of accessible characters (for details please refer to handset's User manual). If your contact on PC has chars outside this set, they can be not displayed properly on handset (or even not displayed at all).
      • [No Title]
        • Open phonebook press the phonebook key
        • Press the right display key
        • Select "Send list"
        • Press the right display key Call to INT
        • Enter the internal number from the handset
        • Press OK

        All entries will be transferred to the designated handset.

  • Downloads

    Hier erhalten Sie Bedienungsanleitungen und Software-Updates.
    Manuals
    • Gigaset SL370 User guide (full version) de AUT

    Firmware
    Software
    • Data Cable USB DCA-510 - driver software version 2.00.8

      Downloaden Sie das ZIP-File, extrahieren Sie es und lesen Sie unbedingt das beiliegende Readme File bevor Sie diese Software installieren.

      Downloaden und installieren Sie diese Software für gesteigerte Performance und Stabilität.

      Download

    Kompatibilität prüfen

    Kombinieren Sie Gigaset Mobilteile und Basisstationen bzw. Router mit DECT-Funktion
    Prüfen Sie die Kompatibilität zwischen Mobilteilen und Basisstationen anhand ausgewählter Funktionen.

    Mobilteil anmelden

    Sie besitzen eine Gigaset SL370 Basisstation und wollen ein Mobilteil anmelden? 
    Das Gigaset SL370 mit einem Mobilteil koppeln

    Nicht fündig geworden?

    Kontaktieren Sie den Gigaset Kundenservice für persönliche Hilfestellung.
Vergleichen